Network Kit X 7 1

The current marine industry standard. All current Raymarine MFDs are NMEA2000 certified. The standard utilizes the CAN (Control Area Network) design developed by Bosch for the automotive market but with messages/sentence appropriate for the marine industry.

• Network Kit X 7 12
• Network Kit X 7 1/4

• Watch commercial-free episodes of your favorite Food Network cooking shows and get direct access to recipes. Start Your 30-day Free Trial. Less Than $1 Per Week.
• 1.8.x Kit PvP Practice BungeeCord Combat Crates Custom Map Abilities Economy Events Kits TOPG.ORG 2019 - 2020 Trademarks are the property of their respective owners, all.

Kit includes QTY: 2 square shoulder U-bolts (3.125' Wide x 4' Long) with 1/2'-13 threads, QTY: 4 Flat Washers 1/2', and QTY: 4 Nylock Nuts 1/2'. $7.05 Qty: Add to Cart.

A multi-talker, multi-listener approach using serial data at moderate date rates (250kbs).

Cable System

Under the NMEA standard, manufacturers can use the cable/connector design of their choice so long as it conforms to certain requirements. The topology is a robust terminated backbone/spur design.

SeaTalk^ng

Raymarine's proprietary cable system for use in NMEA 2000 networks. The design provides two advantages. First, the connector collars are retained on the product which allows for a smaller cable diameter making installations easier. More importantly, the cable can include a sixth wire which allows for backward compatibility with SeaTalk¹ equipment. Products with SeaTalk^ng connectors can be used on NMEA 2000 networks that use Devicenet cabling through simple connector adaptors and conversely equipment with Devicenet connectors can be used on NMEA 2000 networks that use SeaTalk^ng cabling through simple connector adaptors.

Created for the factory automation industry, Devicenet has been approved by the NMEA for NMEA 2000 installations.

Backbone Cables

In a SeaTalk^ng installation, a backbone cable runs through the length of the boat.

Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.

Two backbone cable lengths can be joined together by part A06030, a backbone extender.

Spur Cables

Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone.

Used for connecting white SeaTalk^ng Spur Cables to Blue SeaTalk^ng Backbone Cables

Used for connecting spurs to the backbone

Used for extending blue SeaTalk^ng Backbone Cables

Go at each end of SeaTalk backbone, two are required per system.

Place blanking plug in unused SeaTalk^ng Spur sockets to protect them.

Terminators go at each end of the Backbone. This is ideal for the RS130. Two Terminators are required per system.

Used for connecting SeaTalk1 devices to the SeaTalkng network. See what's in the kit.

Used for connecting an Isolated NMEA 0183 VHF to the SeaTalk^ng network.

Used for connecting SeaTalk1 devices to the SeaTalkng network. Converter only - no cables.

This Starter Kit is perfect to get you going with SeaTalkng. contains: Two Terminators, Power Cable, 5-Way Block, 3m Spur Cable.

This is a larger backbone kit which contains: Two Terminators, Power Cable, 4 x T-Piece Connectors, 20m Backbone Cable, 2 x 5m Backbone Cable

SPX Course Computer Spur Cable (900mm), for connection to SeaTalk^ng. This is supplied with the SPX. (Not applicable to the SPX5)

This is a 90°, right angle spur connector. Used for the multifunction displays.

Raymarine cable kit for NMEA gateway

Power Cables

Backbone Cables

Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone.

Used for connecting white SeaTalk^ng Spur Cables to Blue SeaTalk^ng Backbone Cables

Used for connecting spurs to the backbone

Used for extending blue SeaTalk^ng Backbone Cables

Go at each end of SeaTalk backbone, two are required per system.

Place blanking plug in unused SeaTalk^ng Spur sockets to protect them.

Terminators go at each end of the Backbone. This is ideal for the RS130. Two Terminators are required per system.

Used for connecting SeaTalk1 devices to the SeaTalkng network. See what's in the kit.

Used for connecting an Isolated NMEA 0183 VHF to the SeaTalk^ng network.

Used for connecting SeaTalk1 devices to the SeaTalkng network. Converter only - no cables.

This Starter Kit is perfect to get you going with SeaTalkng. contains: Two Terminators, Power Cable, 5-Way Block, 3m Spur Cable.

This is a larger backbone kit which contains: Two Terminators, Power Cable, 4 x T-Piece Connectors, 20m Backbone Cable, 2 x 5m Backbone Cable

SPX Course Computer Spur Cable (900mm), for connection to SeaTalk^ng. This is supplied with the SPX. (Not applicable to the SPX5)

This is a 90°, right angle spur connector. Used for the multifunction displays.

Raymarine cable kit for NMEA gateway

Power Cables

Backbone Cables

In a SeaTalk^ng installation, a backbone cable runs through the length of the boat.

Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone. The backbone carries both data and power to attached devices. The backbone should be sized so that it will run past every location where an NG or NMEA 2000 device might be installed.

Two backbone cable lengths can be joined together by part A06030, a backbone extender.

Spur Cables

Individual devices connect to the backbone by spur cables that run to T-pieces on the backbone.

Used for connecting white SeaTalk^ng Spur Cables to Blue SeaTalk^ng Backbone Cables

Used for connecting spurs to the backbone

Used for extending blue SeaTalk^ng Backbone Cables

Go at each end of SeaTalk backbone, two are required per system.

Place blanking plug in unused SeaTalk^ng Spur sockets to protect them.

Terminators go at each end of the Backbone. This is ideal for the RS130. Two Terminators are required per system.

Used for connecting SeaTalk1 devices to the SeaTalkng network. See what's in the kit.

Used for connecting an Isolated NMEA 0183 VHF to the SeaTalk^ng network.

Used for connecting SeaTalk1 devices to the SeaTalkng network. Converter only - no cables.

This Starter Kit is perfect to get you going with SeaTalkng. contains: Two Terminators, Power Cable, 5-Way Block, 3m Spur Cable.

This is a larger backbone kit which contains: Two Terminators, Power Cable, 4 x T-Piece Connectors, 20m Backbone Cable, 2 x 5m Backbone Cable

SPX Course Computer Spur Cable (900mm), for connection to SeaTalk^ng. This is supplied with the SPX. (Not applicable to the SPX5)

This is a 90°, right angle spur connector. Used for the multifunction displays.

Raymarine cable kit for NMEA gateway

Network Kit X 7 12

Power Cables

Network Kit X 7 1/4